Ventilation & AHU
Industrial air handling units, ducted supply and extract networks engineered for continuous-duty operation — balanced, commissioned and documented against design airflow.
- Air handling units
- Exhaust systems
- Duct balancing
Engineered Climate & Safety Solutions
Precision HVAC, industrial cooling, and FHN-certified fire protection systems designed for maximum operational reliability.
Baku / AZ · 40.40°N 49.87°E
Air handling unitsVRF systemsSprinkler networksSmoke evacuationChiller plantBoiler roomsDuct balancingKitchen extractionCCTV & wiringFHN certified
Approach
A ventilation system is only as honest as the day it was commissioned. We design, install and balance every scope in-house — so the airflow on the drawing is the airflow in the room.
Expertise
Seven disciplines,
one accountable contractor.
Design, supply, installation and commissioning handled in-house — so the mechanical, fire and electrical scopes never arrive at the same ceiling void with different assumptions.
FHN Licensed
Fire Protection
Sprinkler networks and smoke evacuation systems, designed and commissioned under an active FHN license.
- Sprinkler systems
- Smoke evacuation
Advanced Cooling
VRF, cassette, ducted and multi-split systems, zoned for precise load matching across every occupied volume.
- VRF
- Cassette
- Ducted
- Multi-split
Heating & Hydronics
Boiler installations and centralised heating design, from plant room to final emitter.
- Boiler rooms
- Hydronic design
Chillers & Commercial
Chiller plant and fancoil engineering sized for sustained commercial and industrial loads.
- Chiller plant
- Fancoil
Commercial Kitchens
Stainless steel extraction hoods, preparation tables and ongoing kitchen electrical maintenance.
- Hoods
- Steel tables
- Maintenance
Infrastructure
CCTV monitoring and heavy-duty electrical wiring, installed to carry the plant it serves.
- CCTV
- Heavy-duty wiring
- Distribution
7
Disciplines in-house
Mechanical, fire and electrical scopes under one contract
24/7
Emergency response
Plant failures do not keep office hours
12+
Years on site
Commissioning across Baku and the surrounding regions
240+
Systems commissioned
Balanced against design airflow and documented
Method
From survey
to signature.
Five phases, one contractor carrying the responsibility through all of them.
Survey & load calculation
We walk the building, measure what is already there and calculate the real thermal and airflow load — not the figure the previous contractor assumed.
- Site survey
- Heat & airflow load
- Budget envelope
Design & documentation
Duct routing, plant selection and single-line diagrams drawn against the architecture, with the fire and electrical scopes coordinated in the same model.
- Layout drawings
- Plant schedule
- Coordination set
Supply & procurement
Equipment sourced against the schedule, delivered to programme, with sheet-metal and stainless fabrication produced in-house rather than subcontracted.
- Equipment supply
- Fabrication
- Delivery programme
Installation
Our own crews install the ductwork, plant, pipework and wiring — one accountable team in the ceiling void instead of four trades negotiating for the same 300mm.
- Ductwork & plant
- Pipework
- Power & controls
Commissioning & handover
Every system balanced to its design figures, tested, certified and handed over with the documentation an inspection will ask for.
- Airflow balancing
- Test certificates
- O&M manual
Sectors
Buildings that cannot
afford to stop.
Every sector below has a different failure cost — a hotel loses guests, a plant loses production, a kitchen loses its licence. The load calculation changes accordingly.
Industrial plants
Continuous-duty extract and process cooling
Retail & malls
Large-volume air handling and smoke control
Hotels & hospitality
Zoned VRF with quiet-hours acoustics
Commercial kitchens
Stainless extraction and make-up air
Office buildings
Fancoil and chiller plant with BMS tie-in
Residential complexes
Central heating and multi-split installations
Questions
What clients ask
before the survey.
The questions that come up on almost every first call. If yours is not here, call — the numbers at the bottom of this page go straight to the team.
No. Design, supply, sheet-metal and stainless fabrication, installation and commissioning are all handled by our own crews. That is the point of running seven disciplines in-house: the mechanical, fire and electrical scopes are coordinated in one model instead of negotiated on site between four contractors.
The design and commissioning of fire protection systems — sprinkler networks and smoke evacuation. It is an active licence from the Ministry of Emergency Situations, and it is what lets us sign the fire scope off ourselves instead of handing it to a third party.
It depends on the scope and on what is already in the building, which is why we do not quote a duration before the survey. What is fixed is the sequence: five phases, with a dated delivery programme issued at the procurement phase.
Airflow balancing results measured against the design figures, test certificates for the installed systems, and an O&M manual. That is the set an inspection will ask for, and it is part of the scope rather than an extra.
After the site survey and the heat and airflow load calculation, not before. The first phase ends with a budget envelope built on the measured load — a figure quoted off a floor plan is an assumption, and assumptions are always corrected upward later.
Yes — Baku and the surrounding regions. Distance affects the delivery programme and the response time for maintenance, and both are stated before the contract rather than discovered after it.
We run a 24/7 emergency response. Plant failures do not keep office hours, and a stopped extract system in a kitchen or an industrial hall becomes a licensing and production problem within hours, not days.
Yes. We start by measuring what is actually installed rather than working from the previous contractor's assumed figures — in a system that underperforms, the gap between those two numbers is usually where the fault is.